Skip to content
LumenaryAcademy
Waves 80 min

Antennas and radio links

How a conductor launches a wave into space, how much of it arrives a kilometre or 38,000 kilometres away, and how a receiver digs it out of the noise.

Code tested · 6AI-draftedAwaiting review by an electrical engineer

Your guides: Chloe · The Physicist, Margaret · The Bench Engineer, Gideon · The Design Reviewer

MotivationH

From a voltage to a wave and back

A phone transmitting at a fraction of a watt is heard by a mast several kilometres away. A satellite 38,000 km above the equator delivers a hundred television channels to a dish the size of a bicycle wheel. NASA's Deep Space Network still receives data from the two Voyager probes, launched in 1977 and now more than 20 billion kilometres away, each transmitting with about 20 watts, the power of a refrigerator's light bulb. In every case, a few watts in a conductor become an electromagnetic wave, the wave spreads over an enormous sphere, and a receiver catches a tiny part of it and separates it from the background hiss of thermal noise.

This lesson follows that chain: the antenna, which converts between guided waves on a transmission line and free waves in space; the link budget, which says how much power arrives; noise, which says how much power is needed; the receiver, which brings the signal down to where it can be digitised; and arrays, which shape and steer beams electronically, as the base stations and satellite terminals of 2026 do.

IntuitionH

How antennas radiate

A charge at rest has an electric field; a charge moving steadily drags its field along. Only when a charge accelerates does a kink appear in its field lines, and that kink travels outwards at the speed of light: radiation. An alternating current is charge accelerating back and forth, so any conductor carrying a high-frequency current radiates a little. An antenna is a conductor shaped so that it radiates a lot.

Picture a two-wire transmission line ending in an open circuit. The currents in the two wires flow in opposite directions, so their fields almost cancel at a distance, and the energy is reflected back. Now bend the last quarter-wavelength of each wire outwards until they form a straight line. The currents in the two arms now flow in the same direction, their fields add instead of cancelling, and the energy leaves as a wave. That is a half-wave dipole, the reference antenna of radio engineering.

Close to an antenna the fields are complicated: there is a reactive near field, within about λ/2π\lambda/2\pi, where energy sloshes back and forth between antenna and space without leaving (this is the field an NFC card or a wireless charger uses). Far away, in the far field, the wave has become a spherical wave that looks locally like the plane wave of the previous lessons: E\mathbf{E} and H\mathbf{H} perpendicular, in phase, ∣E∣/∣H∣=η0|\mathbf{E}|/|\mathbf{H}| = \eta_0, and both falling as 1/r1/r, so the power density falls as 1/r21/r^2. For an antenna much larger than a wavelength, such as a dish of diameter DD, the far field starts at about 2D2/λ2D^2/\lambda (28 m for a 60 cm satellite dish at 11.7 GHz). All the formulas below are far-field formulas.

λ/2currentfeedantenna axisno radiation along the axishalf-waveshort dipole (dashed)
A half-wave dipole and its radiation pattern. Left: the current (dashed) is largest at the feed in the middle and falls to zero at the tips. Right: a cut through the radiation pattern containing the antenna's axis (vertical). The dipole radiates most strongly broadside and not at all along its axis; in three dimensions the pattern is a doughnut around the axis. The dashed curve is the slightly fatter pattern of a very short dipole.
DefinitionsH

Pattern, directivity and gain

Definition— radiation pattern and directivity

The radiation intensity U(θ,ϕ)U(\theta, \phi) is the power radiated per unit solid angle in a given direction. An isotropic antenna, which exists only as a reference, would radiate equally in all directions, U=P/4πU = P/4\pi. The directivity DD of a real antenna is the ratio of its peak intensity to the isotropic value: D=4πUmax⁡/PD = 4\pi U_{\max}/P. It is usually quoted in dBi, decibels relative to isotropic.

Definition— gain, efficiency and EIRP

The gain G=ηDG = \eta D includes the antenna's radiation efficiency η\eta, the fraction of the power delivered to it that is radiated rather than lost as heat. The effective isotropic radiated power EIRP=PtGt\text{EIRP} = P_tG_t is the power an isotropic antenna would need to produce the same intensity in the direction of the beam.

Definition— effective aperture

As a receiver, an antenna with gain GG collects power as if it were a perfect absorbing area Ae=Gλ2/4πA_e = G\lambda^2/4\pi facing the wave. For a dish of physical area AA, AeA_e is typically 55–70 % of AA.

The half-power beamwidth is the angle between the directions in which the intensity has fallen to half its peak (−3 dB). Directivity and beamwidth trade against each other: concentrating power into a narrow beam is what makes an antenna directive. A rule of thumb for a dish is a beamwidth of about 70λ/D70\lambda/D degrees.

Analogy, not a formal construction

An antenna's gain is like the reflector of a torch. The bulb does not get brighter when you add a reflector; the same light is gathered into a beam, so the spot in front is brighter and everywhere else is darker. A 30 dBi dish makes a spot a thousand times brighter than a bare bulb would, over a correspondingly small patch of sky.

ExplanationH

The half-wave dipole, computed

The current on a thin half-wave dipole is very nearly a half-cycle of a sine wave, largest at the feed and zero at the tips. Adding up the fields of all its small current elements in the far field gives a radiation intensity proportional to

F(θ)=[cos⁡(π2cos⁡θ)sin⁡θ]2,F(\theta) = \left[\frac{\cos\left(\frac{\pi}{2}\cos\theta\right)}{\sin\theta}\right]^2,

where θ\theta is measured from the antenna's axis. A very short dipole (much shorter than λ\lambda) has the simpler pattern sin⁡2θ\sin^2\theta. The program integrates each pattern over the whole sphere to get the directivity, finds the half-power beamwidth, computes the half-wave dipole's radiation resistance (the resistance that would dissipate the radiated power, Rrad=2P/I02R_{\text{rad}} = 2P/I_0^2), and then looks at short antennas.

python
import numpy as np

eta0 = 376.73
theta = np.linspace(1e-6, np.pi - 1e-6, 200001)     # angle from the antenna's axis
dtheta = theta[1] - theta[0]

def analyse(name, F):
    """F is the radiation intensity pattern (power per steradian, up to a constant)."""
    total = 2 * np.pi * np.sum(F * np.sin(theta)) * dtheta   # integrate over the sphere
    D = 4 * np.pi * F.max() / total                         # directivity: peak / average
    half = theta[F >= F.max() / 2]                          # half-power beamwidth
    hpbw = np.degrees(half[-1] - half[0])
    print(f"{name:20} directivity {D:5.3f} = {10 * np.log10(D):4.2f} dBi, beamwidth {hpbw:5.1f} deg")
    return total

analyse("short dipole", np.sin(theta) ** 2)
F = (np.cos(np.pi / 2 * np.cos(theta)) / np.sin(theta)) ** 2
total = analyse("half-wave dipole", F)

# Radiated power with a peak current I0 is (eta0 I0^2 / 8 pi^2) * total, so R = 2P / I0^2:
print(f"half-wave dipole radiation resistance: {eta0 * total / (4 * np.pi**2):.1f} ohm")

print("\nangle from axis   relative field (half-wave dipole)")
for deg in [0, 15, 30, 45, 60, 75, 90]:
    t = np.radians(max(deg, 1e-6))
    field = np.cos(np.pi / 2 * np.cos(t)) / np.sin(t)
    print(f"{deg:9d} deg   {field:5.3f}  " + "#" * int(round(40 * field)))

# A short centre-fed dipole (current falling linearly to zero at the tips) has
# R_rad = 20 pi^2 (l / lambda)^2. With 0.5 ohm of loss in the wire and matching coil:
for length, f in [(0.10, 100e6), (0.03, 433e6), (1.0, 1e6)]:
    lam = 299_792_458 / f
    r_rad = 20 * np.pi**2 * (length / lam) ** 2
    print(f"{length * 100:5.0f} cm dipole at {f / 1e6:4.0f} MHz: l/lambda = {length / lam:.4f}, "
          f"R_rad = {r_rad:.3f} ohm, efficiency = {100 * r_rad / (r_rad + 0.5):4.1f} %")
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

The half-wave dipole has a directivity of 1.64 (2.15 dBi), a beamwidth of 78°, and a radiation resistance of 73 Ω, which is why a dipole fed directly from a 75 Ω cable, or from 50 Ω with a small mismatch, works well. Engineers quote antenna gains relative to a dipole too, in dBd: 0 dBd = 2.15 dBi.

The short dipoles show the real difficulty of small antennas. Radiation resistance falls as the square of the length in wavelengths, so a 10 cm whip at 100 MHz radiates through a fraction of an ohm, comparable with the resistance of its own wire and matching coil, and only about 30 % of the power gets out. A 1 m wire at 1 MHz is hopeless as a transmitter, which is why medium-wave broadcasting stations use masts a hundred metres or more tall.

Practical antennas are variations on these themes. A monopole over a ground plane (a car's whip, a mast on a roof) is half a dipole with its mirror image in the ground, with half the radiation resistance (about 36 Ω). A patch antenna, a square of copper on a circuit board, radiates from its edges and has a gain of 6–8 dBi. Phone antennas are folded, meandered, multi-band shapes designed by simulation, sharing a tiny volume with metal, battery and hand. A Yagi–Uda antenna (invented by Shintaro Uda and Hidetsugu Yagi at Tohoku University in the 1920s) adds parasitic rods in front of and behind a dipole to make a beam, and still sits on rooftops for television reception. A parabolic dish focuses a plane wave onto a small feed, and its gain grows as (πD/λ)2(\pi D/\lambda)^2.

ExplanationH

The Friis equation

How much of the transmitted power reaches the receiver? Harald Friis of Bell Laboratories put the answer into one line in 1946.

Theorem— Friis transmission equation

In free space, with transmitter and receiver in each other's far field, polarisations matched, and both antennas matched to their lines, the received power is

Pr=Pt Gt Gr(λ4πd)2.P_r = P_t\,G_t\,G_r\left(\frac{\lambda}{4\pi d}\right)^2.

In decibels: Pr=Pt+Gt+Gr−FSPLP_r = P_t + G_t + G_r - \text{FSPL}, where the free-space path loss is FSPL=20log⁡10(4πd/λ)\text{FSPL} = 20\log_{10}(4\pi d/\lambda) dB.

Proof

An isotropic transmitter spreads PtP_t evenly over a sphere of area 4πd24\pi d^2; a transmitting antenna with gain GtG_t multiplies the power density in its beam by GtG_t, giving S=PtGt/(4πd2)S = P_tG_t/(4\pi d^2). The receiving antenna captures the power falling on its effective aperture Ae=Grλ2/4πA_e = G_r\lambda^2/4\pi. Multiplying, Pr=SAe=PtGtGrλ2/(4πd)2P_r = S A_e = P_tG_tG_r\lambda^2/(4\pi d)^2.

∎

Two features are worth noticing. The received power falls as 1/d21/d^2, so doubling the distance costs only 6 dB; radio links span enormous ranges because their loss grows only logarithmically in decibels. And the frequency enters only through λ2\lambda^2, and only because we fixed the antennas' gains. A wave does not "weaken" faster at high frequency in free space: an antenna of a given gain simply has a smaller capture area at shorter wavelengths. (Real links do lose more at high frequency to rain, foliage, walls and the oxygen and water vapour of the atmosphere, which the ITU's propagation models describe.)

ExplanationH

Noise: kTB and the noise figure

A received power means nothing until it is compared with noise. The electrons in any resistor at temperature TT jiggle randomly and produce a noise voltage (Johnson–Nyquist noise), and the noise power a matched receiver picks up in bandwidth BB is

N=kTB,N = kTB,

with Boltzmann's constant k=1.380649×10−23k = 1.380649\times10^{-23} J/K. At the standard reference temperature T0=290T_0 = 290 K this is −174-174 dBm per hertz of bandwidth: −101-101 dBm in a 20 MHz channel, −89-89 dBm in 80 MHz once a typical receiver's own noise is added. A wider channel carries more data but lets in more noise; that trade is the subject of information theory.

Every amplifier, mixer and lossy cable adds noise of its own. The noise factor FF of a stage is the ratio of the signal-to-noise ratio at its input to that at its output, when the input noise is kT0BkT_0B; in decibels it is the noise figure NF. A perfect stage has F=1F = 1 (0 dB). Equivalently, a stage behaves like a noiseless one with an extra noise temperature Te=T0(F−1)T_e = T_0(F - 1) at its input. A passive loss of LL dB at room temperature has a noise figure of LL dB.

Theorem— Friis formula for noise

A chain of stages with noise factors F1,F2,F3,…F_1, F_2, F_3, \ldots and power gains G1,G2,…G_1, G_2, \ldots has total noise factor

F=F1+F2−1G1+F3−1G1G2+⋯F = F_1 + \frac{F_2 - 1}{G_1} + \frac{F_3 - 1}{G_1G_2} + \cdots

Each stage's noise is divided by all the gain in front of it, so the first stage dominates: put a high-gain, low-noise amplifier (LNA) right at the antenna and the rest of the chain hardly matters. The program compares three orderings of the same parts.

python
import math

def cascade(stages, T0=290.0):
    """Friis's formula for noise: stages are (name, gain_dB, noise_figure_dB), antenna first."""
    F_total, G_before = 0.0, 1.0
    for i, (name, g_db, nf_db) in enumerate(stages):
        F = 10 ** (nf_db / 10)
        F_total += F if i == 0 else (F - 1) / G_before
        G_before *= 10 ** (g_db / 10)
    return 10 * math.log10(F_total), T0 * (F_total - 1)

lna = ("low-noise amplifier", 18.0, 1.0)
cable = ("cable and filter", -3.0, 3.0)      # a passive loss of L dB has a noise figure of L dB
mixer = ("mixer", -7.0, 8.0)
if_amp = ("IF amplifier", 30.0, 4.0)

for label, chain in [("LNA at the antenna", [lna, cable, mixer, if_amp]),
                     ("cable first, then LNA", [cable, lna, mixer, if_amp]),
                     ("no LNA at all", [cable, mixer, if_amp])]:
    nf, te = cascade(chain)
    sensitivity = -174 + 10 * math.log10(20e6) + nf + 10    # 20 MHz, 10 dB SNR needed
    print(f"{label:24} NF = {nf:5.2f} dB, Te = {te:6.0f} K, sensitivity = {sensitivity:6.1f} dBm")
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

With the LNA first, the whole chain has a noise figure of 2.3 dB, only 1.3 dB worse than the LNA alone. Put 3 dB of cable in front of the LNA and the cable's loss adds directly to the noise figure, giving 4.7 dB; leave the LNA out and it is 14.4 dB. The last column turns this into sensitivity, the weakest signal the receiver can use (here: noise in 20 MHz plus the noise figure plus a 10 dB signal-to-noise ratio needed by the demodulator): the good design hears signals 12 dB weaker than the one without an LNA, which in free space is four times the range. This is why satellite dishes carry their LNA at the focus, in the "LNB" box on the arm, rather than at the end of the cable indoors.

ExplanationH

Receiver architectures

The received signal may be at 2.4 GHz or 11.7 GHz and as weak as 10−1210^{-12} W. It must be filtered from neighbouring signals that may be a million times stronger, amplified, and brought down to a frequency where it can be demodulated or digitised. Three architectures do this.

SuperheterodyneDirect conversion (zero-IF)RF filterLNALOtunableIF filterIF ampdemodulateaudio, datafixed IFRF filterLNALO 0°/90°low-passlow-passADCADCdigitalprocessingIQ
Two receiver architectures. Top: the superheterodyne mixes the amplified signal with a tunable local oscillator (LO) to a fixed intermediate frequency (IF), where sharp filters and most of the gain are. Bottom: the direct-conversion receiver mixes with two copies of the LO, 90° apart, straight to zero frequency, producing the in-phase (I) and quadrature (Q) components, which are filtered and digitised.

The superheterodyne. Edwin Armstrong's 1918 invention mixes the incoming signal at fRFf_{RF} with a local oscillator at fLOf_{LO}; the mixer (a multiplier) produces the sum and difference frequencies, and the difference fIF=∣fRF−fLO∣f_{IF} = |f_{RF} - f_{LO}| is kept. Tuning the receiver means tuning only the LO, while the selective filters and the gain sit at one fixed IF (10.7 MHz in FM radios, for example). The catch is the image frequency: a signal at fLO+fIFf_{LO} + f_{IF} (if the LO is above the wanted signal) produces the same IF and cannot be separated after the mixer, so the RF filter in front must remove it. Superhets dominated radio for most of the twentieth century and still appear in demanding receivers, often with two or three IFs.

Direct conversion (zero-IF). Choose fLO=fRFf_{LO} = f_{RF}, so the IF is zero. A single mixer would fold the upper and lower halves of the signal's spectrum on top of each other, so the receiver uses two mixers with LOs 90° apart and keeps both outputs, the I and Q components: together they are the real and imaginary parts of the complex envelope of phasors, which preserves everything. There is no image to filter and the channel filters are simple low-pass filters that can be integrated on a chip, which is why almost every phone and Wi-Fi radio is direct-conversion (or "low-IF", a close relative). The price is sensitivity to DC offsets, LO leakage and I/Q imbalance, which are corrected digitally.

Software-defined radio (SDR). Move the analog-to-digital converter as close to the antenna as possible and do the rest in software. Low-cost SDR receivers digitise a few megahertz of I/Q samples after a direct-conversion or low-IF front end; base stations and test equipment use RF-sampling converters that digitise gigahertz of spectrum directly, as sampling and the FFT allows. Filtering, tuning and demodulation are then FFTs and digital filters, and a new standard can be supported by new software. Free toolkits such as GNU Radio let anyone build a receiver this way.

Note

Listening with an inexpensive SDR receiver and a home-made wire dipole is safe and is a superb way to learn this subject, though some countries restrict listening to certain services, so check the rules where you live. Transmitting is different: outside licence-exempt devices such as Wi-Fi routers and toy walkie-talkies, it needs a licence, because a careless transmitter can block emergency and aviation radio. Amateur radio licences, available in most countries through national societies (see the IARU), are the legal way to experiment with transmitters. Never put up an antenna near overhead power lines, and keep away from the antennas of broadcast and mobile-network transmitters, which are fenced for good reason.

ExplanationH

Arrays and beam steering

A dish points its beam by moving. An array of small antennas can point it electronically, in microseconds, and form several beams at once. The idea is interference: feed NN identical elements spaced dd apart along a line, with element nn given a phase shift nφn\varphi. In a direction at angle θ\theta from broadside, the wave from element nn has travelled an extra ndsin⁡θnd\sin\theta, a phase of nkdsin⁡θnkd\sin\theta with k=2π/λk = 2\pi/\lambda. The total field is the element's own pattern times the array factor

AF(θ)=∑n=0N−1ejn(kdsin⁡θ+φ).AF(\theta) = \sum_{n=0}^{N-1} e^{jn(kd\sin\theta + \varphi)}.

All NN terms line up, and ∣AF∣|AF| reaches its maximum NN, in the direction where kdsin⁡θ+φ=0kd\sin\theta + \varphi = 0. So choosing φ=−kdsin⁡θ0\varphi = -kd\sin\theta_0 steers the beam to θ0\theta_0. The sum is a geometric series, which gives ∣AF∣=∣sin⁡(Nψ/2)/sin⁡(ψ/2)∣|AF| = |\sin(N\psi/2)/\sin(\psi/2)| with ψ=kdsin⁡θ+φ\psi = kd\sin\theta + \varphi: the same function as the frequency response of a moving-average filter in digital filters, because an array samples the wave in space just as a filter samples a signal in time.

0φ2φ3φ4φ5φdsplitter / combinerbeam, θ = 30°wavefrontsphaseshifters
A phased array of six elements spaced d apart, each fed through a phase shifter. Giving element n a phase shift nφ, with φ = −kd sin θ, tilts the wavefronts so that the beam leaves at angle θ from broadside (here 30°).
python
import numpy as np

def array_factor(theta_deg, n, d_over_lambda, steer_deg):
    """|AF| / n for n isotropic elements spaced d apart along a line, phased to point at steer_deg
    (angles measured from broadside, i.e. from the direction perpendicular to the line)."""
    theta = np.radians(theta_deg)[:, None]
    k_d = 2 * np.pi * d_over_lambda
    phase = -k_d * np.sin(np.radians(steer_deg))          # progressive phase shift per element
    m = np.arange(n)[None, :]
    return np.abs(np.exp(1j * m * (k_d * np.sin(theta) + phase)).sum(axis=1)) / n

angles = np.arange(-90, 91, 0.1)
for n, d, steer in [(8, 0.5, 0), (8, 0.5, 30), (16, 0.5, 30), (8, 1.0, 30)]:
    af = array_factor(angles, n, d, steer)
    main = angles[(af >= 1 / np.sqrt(2)) & (np.abs(angles - steer) < 20)]   # half-power points
    lobes = [round(float(a)) + 0 for i, a in enumerate(angles[1:-1], 1)
             if af[i] > af[i - 1] and af[i] >= af[i + 1] and af[i] > 0.9]
    print(f"N = {n:2d}, d = {d} lambda, steered to {steer:2d} deg: half-power beamwidth "
          f"{main[-1] - main[0]:4.1f} deg, full-strength beams at {lobes} deg")

print("\nN = 8, d = lambda/2, steered to 30 deg (|AF| in dB, 10 deg steps)")
for a in range(-90, 91, 10):
    v = array_factor(np.array([a]), 8, 0.5, 30)[0]
    level = max(20 * np.log10(max(v, 1e-6)), -30)
    print(f"{a:4d} deg {level:6.1f} dB |" + "#" * int(round(level + 30)))
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

Eight elements half a wavelength apart give a beam about 13° wide; sixteen halve it, since the array is twice as long. Steering to 30° widens the beam slightly, to about 12.8°/cos⁡30°12.8°/\cos 30°, because the array looks shorter seen from an angle. Between the nulls are sidelobes, the highest about 13 dB down, which designers lower by tapering (feeding the edge elements less strongly) at the price of a wider main beam. The last case is a warning: with elements a full wavelength apart, steering to +30° also produces a full-strength grating lobe at −30°, sending half the power the wrong way. To steer anywhere without grating lobes, elements must be at most half a wavelength apart.

Phased arrays are no longer exotic. A 5G base station's "massive MIMO" panel holds 32 to 64 transceivers behind hundreds of elements and forms separate beams towards different users; low-Earth-orbit satellite user terminals are flat phased arrays tracking satellites across the sky; and radars, from weather radars to car radars at 77 GHz, steer electronically. Modern arrays often apply phases and amplitudes digitally, one transceiver per element or group, which is digital beamforming, and the MIMO capacity it unlocks is computed in wireless systems.

ExplanationH

The professional view

  • Design and measurement. Antennas are designed with electromagnetic simulators (FDTD, finite elements and the method of moments from the first lesson of this level; the public-domain NEC-2 code from Lawrence Livermore is a classic for wire antennas) and measured in anechoic chambers lined with radio-absorbing foam, or with near-field scanners that measure close in and compute the far field by a Fourier transform.
  • Link budgets in practice. Professional budgets add fade margins for rain and multipath, use statistical propagation models from ITU-R recommendations or 3GPP channel models rather than free space, and are run across thousands of locations in network-planning software.
  • Over-the-air testing. Phones and base stations with integrated arrays have no connector to plug a cable into at millimetre-wave frequencies, so their performance is certified over the air in chambers, following test plans written by industry bodies.
  • Receivers on a chip. A phone's radio front end is a few chips containing direct-conversion transceivers for many bands, with filters (acoustic-wave devices) and switches in a front-end module; the digital back end is part of the modem.
Common misconceptionsH

Common misconceptions

Misconception

"A high-gain antenna amplifies the signal." An antenna is passive. Its gain is directivity times efficiency, always relative to an isotropic antenna radiating the same total power, and it is bought by radiating less in other directions. A 20 dBi antenna pointed the wrong way receives less than a 0 dBi one.

Misconception

"Higher frequencies suffer more free-space loss because the air absorbs them." Free-space path loss involves no air at all. The 20log⁡10f20\log_{10}f term appears only because an antenna of fixed gain has a smaller effective aperture at higher frequency. With fixed-size dishes at both ends, the gains grow as f2f^2 each and a higher frequency gives a stronger link. Atmospheric absorption is real but separate, and matters mostly above about 20 GHz and in rain.

Misconception

"Turning up the receiver's gain lets it hear weaker signals." Gain amplifies signal and noise together. Sensitivity is set by the noise figure of the first stages and the bandwidth, not by how much gain follows.

Misconception

"The antenna should be a quarter or half wavelength long, or it will not work at all." Resonant lengths make matching easy and efficiency high, but any conductor radiates. Electrically small antennas work, with low radiation resistance, narrow bandwidth and careful matching, as every phone and smartwatch shows.

Exercises

Exercises

1. Antennas and radio links

Warm-upHuman

What is the free-space path loss at 2.4 GHz over 100 m, in dB, to the nearest whole number? Use c=3.0×108c = 3.0 \times 10^8 m/s.

2. Antennas and radio links

Warm-upHuman

What is the thermal noise power kTBkTB at T=290T = 290 K in a 20 MHz channel, in dBm, to the nearest whole number? (Recall that kT0kT_0 is about −174-174 dBm per hertz.)

3. Antennas and radio links

CoreHuman

A Wi-Fi access point's datasheet says its antenna has a gain of 6 dBi. What does this mean?

Choose one

5. Antennas and radio links

CoreHuman

An FM superheterodyne receiver is tuned to a station at 100.0 MHz. It uses an intermediate frequency of 10.7 MHz with the local oscillator above the wanted signal. At what frequency is the image, the other frequency that the mixer also converts to 10.7 MHz? Give it in kHz.

6. Antennas and radio links

CoreComputational

Write cascade_nf(stages), where stages is a list of (gain_dB, noise_figure_dB) pairs in order from the antenna, returning the noise figure of the whole chain in dB by Friis's formula for noise:

F=F1+F2−1G1+F3−1G1G2+⋯F = F_1 + \frac{F_2 - 1}{G_1} + \frac{F_3 - 1}{G_1G_2} + \cdots

Remember to convert decibels to ratios before using the formula, and back at the end. The tests include the three chains from the lesson and two passive losses in a row.

Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

7. Antennas and radio links

StretchComputational

Write array_pattern(n, d_over_lambda, steer_deg, theta_deg), returning the normalised array factor ∣AF(θ)∣/n|AF(\theta)|/n of n isotropic elements in a line, spaced d_over_lambda wavelengths apart, with progressive phase φ=−kdsin⁡θ0\varphi = -kd\sin\theta_0 that steers the beam to steer_deg. theta_deg is a NumPy array of angles from broadside, and the function returns an array of the same shape.

The tests check the broadside beam, the first null of an 8-element array, steering to several angles, and the grating lobe that appears with one-wavelength spacing.

Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

Further reading and resources

  • GNU RadioThe free, open-source toolkit for software-defined radio, with tutorials that start from a first receiver.
  • International Amateur Radio UnionThe federation of national amateur radio societies, which explain how to obtain a licence to transmit in each country.
  • ITU Radiocommunication Sector (ITU-R)Publishes the Radio Regulations and the propagation models used in professional link budgets.
  • A Note on a Simple Transmission Formula · Harald T. Friis · 1946Proceedings of the IRE, vol. 34. The two-page paper that introduced the transmission equation in this lesson.
  • Noise Figures of Radio Receivers · Harald T. Friis · 1944Proceedings of the IRE, vol. 32. Where the noise figure and the cascade formula were defined.
  • NEC-2: Numerical Electromagnetics Code · G. J. Burke and A. J. Poggio, Lawrence Livermore National Laboratory · 1981A long-established method-of-moments program for wire antennas; free and open-source versions are widely available.