Skip to content
LumenaryAcademy
Mechanics 75 min

Rigid-body dynamics

When size and rotation matter — planar kinematics, moments of inertia computed for real shapes, the Newton–Euler equations, rolling, energy methods and a first look at gyroscopes.

Code tested · 5AI-draftedAwaiting review by a mechanical engineer

Your guides: Chloe · The Designer, Margaret · The Test Engineer, Gideon · The Checker

MotivationH

When size and rotation matter

In Dynamics of particles a lorry was a point. That was fine for how far it takes to stop, but useless for the questions that keep vehicle engineers busy: how much of the load moves onto the front tyres when it brakes, whether it lifts a wheel on a bend, how hard the brakes must grip to stop the spinning wheels as well as the lorry. Once the turning of a body matters, it is a rigid body: a body whose points keep their distances from each other, so that its whole motion is described by the motion of one point and one angle.

Rigid bodies are everywhere in machines: wheels and gears, crankshafts and connecting rods, flywheels, the links of a robot arm, the rotor of a wind turbine, a door swinging shut. This lesson stays in the plane, where a body has three degrees of freedom (xx, yy and an angle θ\theta), which covers most machine elements and vehicles. Two new ingredients appear. The moment of inertia says how hard a body is to spin up, the way mass says how hard it is to push. And the second law grows a twin: forces set the acceleration of the centre of mass, moments set the angular acceleration. At the end, a brief excursion into three dimensions explains why a spinning wheel seems to defy gravity.

DefinitionsH

Planar kinematics of a rigid body

A rigid body in the plane can translate (every line in it keeps its direction), rotate about a fixed axis (a wheel on a fixed shaft), or do both at once in general plane motion (a rolling wheel, a connecting rod). Every line drawn on a rigid body turns through the same angle in the same time, so the body has a single angular velocity ω=θ˙\omega = \dot\theta and angular acceleration α=θ¨\alpha = \ddot\theta.

Definition— relative velocity and acceleration in a rigid body

For two points A and B of a rigid body in plane motion, with rB/A\mathbf r_{B/A} the vector from A to B, ω=ω k\boldsymbol\omega = \omega\,\mathbf k and α=α k\boldsymbol\alpha = \alpha\,\mathbf k perpendicular to the plane,

vB=vA+ω×rB/A,aB=aA+α×rB/A−ω2 rB/A.\mathbf v_B = \mathbf v_A + \boldsymbol\omega \times \mathbf r_{B/A}, \qquad \mathbf a_B = \mathbf a_A + \boldsymbol\alpha \times \mathbf r_{B/A} - \omega^2\,\mathbf r_{B/A}.

Seen from A, B simply moves on a circle round it: ωr\omega r across the line AB, plus, for acceleration, αr\alpha r across it and ω2r\omega^2 r towards A.

For a body rotating about a fixed axis O, set A = O: a point at radius rr has speed ωr\omega r, tangential acceleration αr\alpha r and centripetal acceleration ω2r\omega^2 r. For general plane motion there is, at each instant, one point of the body (or of its imaginary extension) whose velocity is zero, the instantaneous centre of zero velocity; at that instant the body is turning about it, and every point's velocity is ω\omega times its distance from it, at right angles to the line joining them.

Definition— rolling without slipping

A wheel of radius RR rolls without slipping on a fixed surface when its contact point has zero velocity. Then the centre moves at vG=ωRv_G = \omega R, and if the surface is straight, aG=αRa_G = \alpha R.

v2v√2 v√2 vP: at restGrolling to the right:v = ωR, clockwise ω
The velocities of points on a wheel rolling to the right without slipping. The contact point P is the instantaneous centre: it is momentarily at rest, and every other point moves at right angles to its line from P, at a speed proportional to its distance from P. The centre moves at v, the top at 2v, and points level with the centre at √2 v.

Example— Points on a bicycle wheel

A bicycle with 0.34 m wheels rides at 6.0 m/s. Rolling without slipping, each wheel turns at ω=v/R=17.6\omega = v/R = 17.6 rad/s. The top of the tyre moves at 2v=122v = 12 m/s, the point touching the road is at rest, and the valve, when it passes level with the hub at the front, moves at 2 v=8.5\sqrt 2\,v = 8.5 m/s, forwards and downwards. That is why the spokes at the top of a moving wheel blur in a photograph while those at the bottom look sharp.

DefinitionsH

Moments of inertia

Definition— moment of inertia, radius of gyration

The moment of inertia of a body about an axis is I=∫r2 dmI = \int r^2\,\mathrm dm, where rr is the distance of each element of mass dm\mathrm dm from the axis, in kg m². The radius of gyration kk is defined by I=mk2I = mk^2: the radius at which all the mass, concentrated in a ring, would have the same moment of inertia.

Because of the r2r^2, mass far from the axis counts for much more than mass near it. For uniform bodies about an axis through the centre of mass G, perpendicular to the plane of motion, the standard results are: a thin rod of length LL, mL2/12mL^2/12; a solid disc or cylinder of radius RR, mR2/2mR^2/2; a thin ring or pipe, mR2mR^2; a rectangular plate a×ba \times b, m(a2+b2)/12m(a^2 + b^2)/12; a solid sphere about a diameter, 25mR2\tfrac25 mR^2; a thin spherical shell, 23mR2\tfrac23 mR^2. These come from the integral by the methods of multivariable calculus, and CAD software computes the same integral for any modelled part. Most real parts are assembled from simpler ones, which is where the next theorem earns its keep.

Theorem— Parallel-axis theorem

If IGI_G is the moment of inertia of a body of mass mm about an axis through its centre of mass G, its moment of inertia about any parallel axis a distance dd away is I=IG+md2I = I_G + md^2.

Proof

Put G at the origin and the new axis through the point (dx,dy)(d_x, d_y), with d2=dx2+dy2d^2 = d_x^2 + d_y^2. Then I=∫[(x−dx)2+(y−dy)2] dm=∫(x2+y2) dm−2dx ⁣∫x dm−2dy ⁣∫y dm+d2 ⁣∫dmI = \int\big[(x - d_x)^2 + (y - d_y)^2\big]\,\mathrm dm = \int (x^2 + y^2)\,\mathrm dm - 2d_x\!\int x\,\mathrm dm - 2d_y\!\int y\,\mathrm dm + d^2\!\int \mathrm dm. The first integral is IGI_G, the middle two vanish because G is the centre of mass, and the last is md2md^2.

∎

So IGI_G is the smallest moment of inertia about any axis in a given direction. A thin rod about one end has mL2/12+m(L/2)2=mL2/3mL^2/12 + m(L/2)^2 = mL^2/3, four times its value about the middle.

The program below computes moments of inertia the way a computer does for an arbitrary flat shape: cover it with a fine grid, keep the cells inside, and add up r2 dmr^2\,\mathrm dm. It checks the method on three shapes with known answers, then applies it to a steel flywheel with four lightening holes, and compares the result with the parallel-axis theorem: the full disc, minus four small discs, each about its own centre plus md2md^2.

python
import numpy as np

def lamina(inside, box, mass, n=1000):
    """Moment of inertia of a flat plate of uniform density about the axis perpendicular to it
    through its centre of mass, by the midpoint rule on an n x n grid over box = (x0, x1, y0, y1)."""
    x0, x1, y0, y1 = box
    hx, hy = (x1 - x0) / n, (y1 - y0) / n
    x, y = np.meshgrid(x0 + hx * (np.arange(n) + 0.5), y0 + hy * (np.arange(n) + 0.5))
    w = inside(x, y)                                   # True inside the shape
    area = w.sum() * hx * hy
    rho = mass / area                                  # mass per unit area (kg/m^2)
    xc, yc = x[w].mean(), y[w].mean()                  # centre of mass
    I_G = rho * hx * hy * ((x[w] - xc) ** 2 + (y[w] - yc) ** 2).sum()
    return I_G, (xc, yc)

# Check the method on shapes with known answers (masses in kg, lengths in m).
m, R, a, b = 10.0, 0.20, 0.60, 0.10
disc, _ = lamina(lambda x, y: x**2 + y**2 <= R**2, (-R, R, -R, R), m)
rect, _ = lamina(lambda x, y: np.ones_like(x, bool), (-a / 2, a / 2, -b / 2, b / 2), m)
ring, _ = lamina(lambda x, y: (x**2 + y**2 <= R**2) & (x**2 + y**2 >= 0.15**2), (-R, R, -R, R), m)
print("shape                  numerical   formula")
print(f"disc, m R^2/2          {disc:9.5f}   {m * R**2 / 2:9.5f}")
print(f"plate, m(a^2+b^2)/12   {rect:9.5f}   {m * (a**2 + b**2) / 12:9.5f}")
print(f"ring, m(Ri^2+Ro^2)/2   {ring:9.5f}   {m * (0.15**2 + R**2) / 2:9.5f}")

# A steel flywheel: a 0.40 m disc, 30 mm thick, with four 80 mm lightening holes on a 0.12 m circle.
steel, t = 7850.0, 0.030                             # density (kg/m^3), thickness (m)
R, r, c = 0.20, 0.040, 0.12
holes = [(c * np.cos(q), c * np.sin(q)) for q in np.radians([0, 90, 180, 270])]
def flywheel(x, y):
    keep = x**2 + y**2 <= R**2
    for hx, hy in holes:
        keep &= (x - hx) ** 2 + (y - hy) ** 2 > r**2
    return keep
m_disc, m_hole = steel * t * np.pi * R**2, steel * t * np.pi * r**2
m_fly = m_disc - 4 * m_hole
I_num, G = lamina(flywheel, (-R, R, -R, R), m_fly, n=2000)
# By the parallel-axis theorem: the full disc minus four holes, each about its own centre plus m d^2.
I_pat = m_disc * R**2 / 2 - 4 * (m_hole * r**2 / 2 + m_hole * c**2)
print(f"\nflywheel mass {m_fly:.2f} kg (full disc {m_disc:.2f} kg); centre of mass at "
      f"({abs(G[0]):.4f}, {abs(G[1]):.4f}) m")
print(f"I about its axis: numerical {I_num:.4f} kg m^2, parallel-axis theorem {I_pat:.4f} kg m^2")
print(f"holes remove {100 * 4 * m_hole / m_disc:.1f}% of the mass "
      f"but only {100 * (1 - I_pat / (m_disc * R**2 / 2)):.1f}% of the moment of inertia")
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

The grid method agrees with the formulas to four or five figures, and the flywheel's two answers agree: 0.5199 kg m². Removing material at less than the outer radius saves proportionally more mass than inertia, here 16.0 per cent of the mass for 12.2 per cent of the inertia, and holes nearer the hub would do better still.

DefinitionsH

The Newton–Euler equations in the plane

Treat the body as a cloud of particles, apply Newton's second law to each, and add. The internal forces cancel in pairs, and two equations survive.

Theorem— Newton–Euler equations for plane motion

For a rigid body of mass mm moving in a plane that is a plane of symmetry of the body (or for a thin plate moving in its own plane), with centre of mass G,

∑F=m aG,∑MG=IG α,\sum \mathbf F = m\,\mathbf a_G, \qquad \sum M_G = I_G\,\alpha ,

where ∑MG\sum M_G is the total moment of the external forces about G. If the body rotates about a fixed axis through O, the second equation may be replaced by ∑MO=IO α\sum M_O = I_O\,\alpha.

Proof

Summing miai=Fiext+∑jFijm_i\mathbf a_i = \mathbf F_i^{\text{ext}} + \sum_j \mathbf F_{ij} over all particles, the internal forces cancel by Newton's third law, leaving ∑F=∑miai=maG\sum\mathbf F = \sum m_i\mathbf a_i = m\mathbf a_G by the definition of G. For moments about G, write ri\mathbf r_i from G to particle ii. Then ∑MG=∑ri×miai\sum M_G = \sum \mathbf r_i \times m_i\mathbf a_i (the internal forces act along the lines joining particles, so their moments cancel too). Using the relative-acceleration formula, ai=aG+α×ri−ω2ri\mathbf a_i = \mathbf a_G + \boldsymbol\alpha\times\mathbf r_i - \omega^2\mathbf r_i: the aG\mathbf a_G term gives (∑miri)×aG=0(\sum m_i\mathbf r_i)\times\mathbf a_G = \mathbf 0, the ω2\omega^2 term gives ri×ri=0\mathbf r_i\times\mathbf r_i = \mathbf 0, and the α\alpha term gives ∑miri2 α k=IG α k\sum m_i r_i^2\,\alpha\,\mathbf k = I_G\,\alpha\,\mathbf k. For a fixed axis, repeat with O in place of G, where aO=0\mathbf a_O = \mathbf 0.

∎

The working method is the one from particles, with one more arrow. Draw the free-body diagram; beside it, draw the kinetic diagram, with the vector maGm\mathbf a_G at G and the couple IGαI_G\alpha; and require the two diagrams to have the same resultant and the same moment about any point you like.

Example— Load transfer when a car brakes

A 1500 kg car has a wheelbase of 2.70 m, with G 1.20 m behind the front axle, 1.50 m ahead of the rear axle and 0.55 m above the road. It brakes on all four wheels at 0.8g=7.850.8g = 7.85 m/s². Find the normal forces on the front and rear axles.

The car translates without rotating, so α=0\alpha = 0 and the kinetic diagram is just maGm a_G at G, pointing backwards. The braking forces act backwards at road level, 0.55 m below G. Take moments about the rear contact point, where the kinetic diagram's moment is maGhm a_G h (the line of maGm\mathbf a_G passes 0.55 m above the road):

NfL−mg br=maGh  ⇒  Nf=m(g br+aGh)L=1500(9.81×1.50+7.85×0.55)2.70=10.6 kN,N_f L - mg\,b_r = m a_G h \;\Rightarrow\; N_f = \frac{m(g\,b_r + a_G h)}{L} = \frac{1500(9.81 \times 1.50 + 7.85 \times 0.55)}{2.70} = 10.6 \text{ kN},

and Nr=mg−Nf=4.1N_r = mg - N_f = 4.1 kN. At rest the front axle carries mg br/L=8.2mg\,b_r/L = 8.2 kN, 56 per cent of the weight; braking hard it carries 72 per cent. That load transfer is why front brakes are bigger than rear ones, why brake systems apportion pressure front to rear, and, at the extreme, why a motorcycle braking hard can lift its rear wheel.

Example— A rod released from rest

A uniform rod of mass 6.0 kg and length 1.5 m is pinned at one end and held horizontal, then released. At the instant of release ω=0\omega = 0, and for rotation about the fixed pin O, ∑MO=IOα\sum M_O = I_O\alpha with IO=mL2/3I_O = mL^2/3:

mg L2=mL23 α  ⇒  α=3g2L=9.81 rad/s2.mg\,\frac L2 = \frac{mL^2}{3}\,\alpha \;\Rightarrow\; \alpha = \frac{3g}{2L} = 9.81 \text{ rad/s}^2 .

G then accelerates downwards at αL/2=7.36\alpha L/2 = 7.36 m/s², three-quarters of gg, and vertical force balance on the rod, mg−R=maGmg - R = m a_G, gives a pin force of only R=mg/4=14.7R = mg/4 = 14.7 N. A quarter of the weight: the pin is relieved because the rod is partly falling. The same calculation, with real masses, sizes the hinges, brakes and counterweights of anything that swings: a barrier arm, a bascule bridge leaf, a robot link that loses power.

DefinitionsH

Energy methods for rigid bodies

The work–energy principle from particles carries over once kinetic energy includes rotation.

Definition— kinetic energy of a rigid body in plane motion

T=12mvG2+12IG ω2,T = \tfrac12 m v_G^2 + \tfrac12 I_G\,\omega^2 ,

the energy of the centre of mass moving with the whole mass, plus the energy of rotation about it. For rotation about a fixed axis O this equals 12IO ω2\tfrac12 I_O\,\omega^2. A couple MM turning the body through an angle dθ\mathrm d\theta does work M dθM\,\mathrm d\theta, and delivers power P=MωP = M\omega.

Two facts make energy methods especially handy for rolling. The contact force on a wheel rolling without slipping acts at a point with zero velocity, so static friction there does no work: it moves energy between translation and rotation but removes none. And a wheel's speed then fixes its spin, so one energy equation gives one unknown speed.

Example— Energy in a flywheel

A solid steel disc of 500 kg and radius 0.50 m spins at 6000 rpm, or ω=628\omega = 628 rad/s. Its moment of inertia is 12mR2=62.5\tfrac12 mR^2 = 62.5 kg m², so it stores 12Iω2=12.3\tfrac12 I\omega^2 = 12.3 MJ, about 3.4 kWh. Because energy goes as ω2\omega^2, slowing it to half speed releases three-quarters of that, 9.3 MJ. Its rim moves at 314 m/s, and the hoop stress in a spinning disc grows with the square of the rim speed; at this speed it is around 320 MPa, a large fraction of what a good steel can safely carry. Stress, not size, limits a flywheel's energy per kilogram, which is why storage flywheels use high-strength composite rims and spin in vacuum inside a strong containment.

ComputationC

Rolling, computed

mgNfGθfree-body diagramkinetic diagram=m aGIGα
A body of radius r rolling without slipping down a slope at angle θ. Left: its free-body diagram, with weight mg, the normal force N pushing on it at the contact point, and static friction f there, acting up the slope. Right: its kinetic diagram, the vector m·a_G down the slope and the couple I_G·α. The two diagrams must be equivalent.

Write IG=k mr2I_G = k\,mr^2, where the number kk depends only on the shape: 25\tfrac25 for a solid sphere, 12\tfrac12 for a solid cylinder, 23\tfrac23 for a hollow sphere, 1 for a thin pipe. Down the slope, mgsin⁡θ−f=maGmg\sin\theta - f = ma_G. About G, fr=IGα=k mr2 (aG/r)fr = I_G\alpha = k\,mr^2\,(a_G/r), so f=k maGf = k\,m a_G. Eliminating ff,

aG=gsin⁡θ1+k,f=k1+k mgsin⁡θ.a_G = \frac{g\sin\theta}{1 + k}, \qquad f = \frac{k}{1 + k}\,mg\sin\theta .

Rolling needs f≤μsN=μsmgcos⁡θf \le \mu_s N = \mu_s mg\cos\theta, that is μs≥tan⁡θ k/(1+k)\mu_s \ge \tan\theta\,k/(1 + k); on a steeper slope the body slides and spins at once. Energy gives the speed at the foot directly: mgh=12mv2(1+k)mgh = \tfrac12 m v^2 (1 + k).

python
import numpy as np

g = 9.81
theta = np.radians(10.0)          # slope of the ramp
L = 2.0                           # length of the ramp (m)
h = L * np.sin(theta)

# k = I_G / (m r^2): how much of the body's mass is far from its axis.
shapes = [("block, sliding, no friction", 0.0), ("solid sphere", 2 / 5), ("solid cylinder", 1 / 2),
          ("hollow sphere", 2 / 3), ("thin-walled pipe", 1.0)]

print("body                         a (m/s2)  time (s)  speed at foot  min friction coeff.")
for name, k in shapes:
    a = g * np.sin(theta) / (1 + k)             # Newton-Euler for rolling without slipping
    t = np.sqrt(2 * L / a)
    v = np.sqrt(2 * g * h / (1 + k))            # energy: m g h = (1/2) m v^2 (1 + k)
    mu = np.tan(theta) * k / (1 + k)            # friction needed: f = k m a <= mu m g cos(theta)
    print(f"{name:28s} {a:8.3f} {t:9.3f} {v:10.3f} m/s   {mu:8.3f}")
    assert np.isclose(v, a * t)                 # the two routes agree

# The steepest slope each body can roll down without slipping, if the static friction coefficient is 0.25.
mu_s = 0.25
print("\nsteepest slope for rolling with mu_s = 0.25:",
      ", ".join(f"{name.split(',')[0]} {np.degrees(np.arctan(mu_s * (1 + k) / k)):.1f} deg"
                for name, k in shapes[1:]))
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

On a 2 m ramp at 10°, a frictionless sliding block arrives first, in 1.53 s, then the solid sphere (1.81 s), the solid cylinder, the hollow sphere and last the pipe (2.17 s). The friction needed is small on a gentle slope, but with μs=0.25\mu_s = 0.25 a pipe starts to skid on slopes steeper than 26.6°, while a solid sphere keeps rolling up to 41.2°.

A body that is not rolling to begin with must get there through sliding friction, and this is where step-by-step integration of the Newton–Euler equations earns its place. A snooker cue ball struck through its centre leaves the tip sliding, with no spin. Kinetic friction at the cloth pushes backwards on the contact point: it slows the centre (mv˙=−μkmgm\dot v = -\mu_k mg) and spins the ball up (IGω˙=μkmg RI_G\dot\omega = \mu_k mg\,R), until the contact point stops slipping, v=Rωv = R\omega, and the ball rolls. Strike above the centre and the ball starts with topspin; below, with backspin.

python
import numpy as np

# A snooker ball on the cloth: it slides until its contact point stops slipping, then rolls.
g, mu = 9.81, 0.20                # kinetic friction coefficient, ball on cloth (illustrative)
m, R = 0.17, 0.02625              # mass (kg) and radius (m) of a snooker ball
I = 2 / 5 * m * R**2              # solid sphere about a diameter

def strike(v0, h, dt=1e-5, show=False):
    """A level cue strike at height h above the centre gives speed v0 and spin w0 = m v0 h / I.
    Step the Newton-Euler equations until the ball rolls. Returns (time, distance, speed, spin)."""
    v, w, x, n = v0, m * v0 * h / I, 0.0, 0
    s0 = np.sign(v - R * w)       # the direction in which the contact point slips
    while (v - R * w) * s0 > 0:
        if show and n % 5000 == 0:
            print(f"{n * dt:6.3f} {v:9.3f} {R * w:10.3f} {v - R * w:11.3f} {x:8.3f}")
        F = mu * m * g * s0       # kinetic friction opposes the slip
        v -= F / m * dt           # sum of forces:     m dv/dt = -F
        w += F * R / I * dt       # moments about G:   I dw/dt = F R
        x += v * dt
        n += 1
    return n * dt, x, v, w

print("struck through the centre at 2.0 m/s:")
print("  t (s)   v (m/s)   R w (m/s)  slip (m/s)   x (m)")
t, x, v, w = strike(2.0, 0.0, show=True)
print(f"{t:6.3f} {v:9.3f} {R * w:10.3f} {0.0:11.3f} {x:8.3f}   rolls from here on")
E0, E1 = 0.5 * m * 2.0**2, 0.5 * m * v**2 + 0.5 * I * w**2
print(f"theory: rolls after 2 v0 / (7 mu g) = {2 * 2.0 / (7 * mu * g):.3f} s at 5 v0 / 7 = {5 / 7 * 2.0:.3f} m/s")
print(f"kinetic energy lost to sliding friction: {100 * (1 - E1 / E0):.1f}% (theory: 2/7 = 28.6%)")

print("\ncue height h    spin R w0   slides for            then rolls at")
for h_over_R in [0.0, 0.4, -0.4]:
    Rw0 = m * 2.0 * h_over_R * R / I * R
    t, x, v, w = strike(2.0, h_over_R * R)
    print(f"{h_over_R:+5.1f} R    {Rw0:+8.2f} m/s   {t:5.3f} s and {x:5.3f} m   {v:5.3f} m/s")
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

Struck through its centre at 2.0 m/s, the ball slides for 0.29 s and half a metre, then rolls at 57\tfrac57 of its starting speed, 1.43 m/s, having lost 27\tfrac27 of its kinetic energy to sliding friction, exactly as the closed-form solution predicts. Struck at 0.4R0.4R above the centre, it rolls from the very first instant and loses nothing to sliding: the impulse there gives exactly the spin that rolling needs. Engineers call that height the centre of percussion, and it is why a well-designed hammer, bat or racket has a "sweet spot" where an impact sends no jolt into the hand. Struck at 0.4R0.4R below the centre, the backspin fights the motion, and the ball slides for 0.83 m before rolling on at only 0.86 m/s.

ExplanationH

Gyroscopic effects, in brief

Everything so far happened in a plane, where angular velocity and angular momentum both point along the fixed axis k\mathbf k and only their sizes change. In three dimensions they can change direction, and the results are famously counter-intuitive. For a body spinning fast about its axis of symmetry, the angular momentum is, to a good approximation, H=Iω\mathbf H = I\boldsymbol\omega, along the spin axis, and the rotational form of Newton's second law is

∑MG=dHdt.\sum \mathbf M_G = \frac{\mathrm d\mathbf H}{\mathrm dt}.

A moment changes H\mathbf H in the direction of the moment, not in the direction in which the moment would tip a body at rest.

rpivotside viewmgHHMpostΩtop view
A spinning wheel on an axle supported at one end. Left: side view. The weight acts at the wheel, a distance r from the pivot, and the angular momentum H points along the axle. Right: top view. The weight's moment about the pivot, M = r × mg, is horizontal and at right angles to the axle. It changes H in its own direction, so instead of falling the axle swings round the post, at the precession rate Ω = M/H.

Hang a spinning wheel by one end of its axle and its weight exerts a moment M=mgrM = mgr about the pivot, horizontal and at right angles to the axle. That moment adds angular momentum sideways, so the axle swings round the post, a motion called precession, at a rate Ω=M/(Iω)\Omega = M/(I\omega), instead of dropping. A bicycle wheel of 1.5 kg, with nearly all its mass at a 0.30 m rim (I≈mR2=0.135I \approx mR^2 = 0.135 kg m²), spun at 10 revolutions per second and supported 0.15 m from its centre, precesses at Ω=(1.5×9.81×0.15)/(0.135×62.8)=0.26\Omega = (1.5 \times 9.81 \times 0.15)/(0.135 \times 62.8) = 0.26 rad/s, one turn in about 24 s. Halve the spin and it precesses twice as fast; this simple formula is valid only while the spin is much faster than the precession.

The same equation, read the other way, gives the gyroscopic moment that a machine must supply to turn a spinning rotor: M=Iω ΩM = I\omega\,\Omega. For a rotor with I=20I = 20 kg m² at 6000 rpm (628 rad/s) inside a vehicle turning at 0.2 rad/s, the bearings must carry a moment of 20×628×0.2=2.520 \times 628 \times 0.2 = 2.5 kN m, which is why the rotor bearings of ship and aircraft engines are designed for manoeuvres as well as weight. Engineers also put the effect to work: gyrocompasses that seek true north, gyrostabilisers that reduce the rolling of boats, and control moment gyroscopes that turn space stations and large satellites without using propellant by tilting fast-spinning wheels. The full three-dimensional theory, Euler's equations for a rigid body and the rotation matrices and quaternions that describe its attitude, is developed in Lumenary Robotics' rotations and quaternions and robot dynamics.

History & global context

From the compound pendulum to the gyrocompass

Christiaan Huygens solved the first rigid-body dynamics problem of real consequence in his Horologium Oscillatorium (1673): the period of a swinging body of any shape, which needed what we now call its moment of inertia and its centre of oscillation, for the pendulum clocks he was perfecting. Leonhard Euler named and defined the moment of inertia and, in a series of works culminating in his Theoria motus corporum solidorum seu rigidorum (1765), gave the equations of rigid-body motion in three dimensions that every multibody code still solves. The parallel-axis theorem is often named after the Swiss geometer Jakob Steiner, who studied such relations in the nineteenth century. Léon Foucault demonstrated and named the gyroscope in Paris in 1852, as a way to show the Earth's rotation. Practical gyrocompasses followed in the early twentieth century, from Hermann Anschütz-Kaempfe in Germany and Elmer Sperry in the United States, and gyroscopes went on to guide ships, aircraft and spacecraft until optical and micro-machined (MEMS) gyroscopes took over most of their tasks.

ExplanationH

Rigid-body dynamics in professional practice

Mass properties from CAD. Nobody integrates r2 dmr^2\,\mathrm dm by hand for a real part. CAD systems, from open-source FreeCAD to the commercial packages used across industry, report a part's mass, centre of mass and full inertia tensor from its solid model, and engineers check them against hand estimates like the ones above. For assemblies whose density is uncertain (a car, a satellite, a robot with cables and electronics), inertia is measured, by swinging the object on a calibrated pendulum or a torsional "inertia table" and timing the oscillation.

Balancing rotors. A rotor whose centre of mass is off its axis, or whose principal axis is tilted, pushes on its bearings once every revolution with a force proportional to ω2\omega^2. Fans, turbines, crankshafts and car wheels are therefore balanced, by adding or removing small masses, to quality grades set out in the ISO 21940 series published by ISO. The rotating force that an imbalance creates is the forcing of the next lesson.

Multibody simulation. Vehicles, landing gear, robots and machine tools are modelled as many rigid bodies joined by constraints, and simulated by multibody codes: commercial tools from companies in the United States, Germany, Belgium and South Korea, and open-source engines such as Project Chrono, MuJoCo and Drake, which robotics research relies on. Each of them assembles and integrates the Newton–Euler equations of this lesson, in three dimensions, for every body at every time step.

Safety around rotating machinery. Rotating parts store energy (12Iω2\tfrac12 I\omega^2) and can catch clothing, hair and fingers in an instant. That is why machine-safety standards require fixed guards over belts, couplings and shafts, interlocks that stop a machine before a guard can be opened, and containment around high-speed rotors such as flywheels and turbine wheels. In a school or home workshop, rotating tools are used only with their guards in place, with long hair tied back and loose clothing secured, and with supervision.

Common misconceptionsH

Common misconceptions

Misconception

"A body has a moment of inertia." It has many: one for every axis. The same rod has mL2/12mL^2/12 about its middle and mL2/3mL^2/3 about its end. Always say which axis, and use the parallel-axis theorem to move between parallel ones.

Misconception

"∑M=Iα\sum M = I\alpha works about any point." It works about the centre of mass G and about a fixed axis of rotation. About any other point, the moment of maGm\mathbf a_G must be included, which is exactly what the kinetic diagram is for.

Misconception

"Friction on a rolling wheel always slows it down and wastes energy." Static friction at a contact point that does not slip does no work. On a slope it is what makes the wheel turn; on a driven wheel it is what pushes the vehicle forwards. Energy is lost in rolling only through slip, deformation of tyre and road (rolling resistance), and the bearings.

Misconception

"A heavier ball rolls down a slope faster." For bodies of the same shape rolling without slipping, aG=gsin⁡θ/(1+k)a_G = g\sin\theta/(1 + k) depends only on the shape factor kk, not on mass or size. Until air drag matters, a solid steel ball and a solid glass marble keep pace.

Misconception

"Bicycles stay upright because of the gyroscopic effect of their wheels." The spinning wheels do contribute, but experiments with specially built bicycles whose gyroscopic effects were cancelled showed that a bicycle can still balance itself: steering geometry and the distribution of mass matter at least as much, and a rider's steering most of all.

Exercises

Exercises

Use g=9.81g = 9.81 m/s² throughout. Two exercises ask for Python functions; run them in the editor before submitting.

1. Rigid-body dynamics

Warm-upHuman

A car drives at a steady 72 km/h on a straight road, its tyres rolling without slipping. Relative to the road, how fast are the top of a tyre and the point of the tyre touching the road moving?

Choose one

2. Rigid-body dynamics

Warm-upHuman

A uniform disc of mass 4.0 kg and radius 0.25 m turns about an axis perpendicular to it through a point on its rim (like a disc pinned near its edge and swinging). What is its moment of inertia about that axis? Give your answer in units of 10−310^{-3} kg m² (so 0.1 kg m² would be 100).

3. Rigid-body dynamics

CoreHuman

Four bodies are released together from rest at the top of the same slope: a solid steel ball, a solid wooden cylinder of twice the ball's radius, a thin-walled steel pipe, and an ice cube sliding on a (practically) frictionless film of water. The three round bodies roll without slipping. In which order do they reach the bottom?

Choose one

4. Rigid-body dynamics

CoreHuman

A uniform 8.0 kg rod, 2.0 m long, is pinned at one end and held horizontal. It is released from rest. What is the vertical force on the pin at the instant of release, in newtons, rounded to the nearest newton?

5. Rigid-body dynamics

CoreHuman

A solid steel flywheel disc has a mass of 250 kg and a radius of 0.40 m. It slows from 7200 rpm to 3600 rpm while driving a generator. How much energy does it release, in kJ, rounded to the nearest kJ?

6. Rigid-body dynamics

CoreComputational

Write composite_inertia(parts, axis=(0.0, 0.0)) for a flat body built from parts, moving in its plane. Each part is (m, I_G, x, y): its mass, its moment of inertia about its own centre of mass, and the position of that centre of mass. A hole is a part with negative mass and negative moment of inertia.

Return (I_axis, I_G): the whole body's moment of inertia about the perpendicular axis through the point axis, and about the parallel axis through the whole body's centre of mass.

Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

7. Rigid-body dynamics

StretchComputational

Write incline_motion(theta_deg, k, R, mu_s, mu_k, g=9.81) for a round body of radius R with IG=k mR2I_G = k\,mR^2, released from rest on a slope at theta_deg. Return (a_G, alpha, rolling): the acceleration of its centre down the slope, its angular acceleration, and True if it rolls without slipping.

First assume rolling and check whether static friction can supply the force needed. If it cannot, the body slips: kinetic friction μkN\mu_k N then acts up the slope, and aGa_G and α\alpha are no longer linked by aG=αRa_G = \alpha R.

Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

Further reading and resources

  • MIT OpenCourseWare 2.003SC, Engineering Dynamics · Massachusetts Institute of TechnologyRigid-body kinematics and kinetics, angular momentum and Lagrange's equations, with problem sets.
  • Mechanics Map · Jacob Moore and contributors, Penn StateOpen chapters on rigid-body kinematics, moments of inertia and rigid-body kinetics, with worked examples.
  • A bicycle can be self-stable without gyroscopic or caster effects · J. D. G. Kooijman, J. P. Meijaard, J. M. Papadopoulos, A. Ruina and A. L. Schwab · 2011An experiment and analysis showing that a bicycle's stability does not rest on the gyroscopic effect alone.
  • ISO, the International Organization for StandardizationPublishes the ISO 21940 series on the mechanical balancing of rotors and ISO's machinery-safety standards for guards.
  • FreeCADFree and open-source parametric CAD, which reports the volume, centre of mass and inertia of a modelled part.
  • MuJoCoAn open-source physics engine for articulated rigid bodies, widely used in robotics research.