Skip to content
LumenaryAcademy
Solids 60 min

Stress and strain

What a load does inside a part — the intensity of internal force, the stretch it causes, the curve that says when the material gives up, and how the same stress looks from every direction.

Code tested · 4AI-draftedAwaiting review by a mechanical engineer

Your guides: Chloe · The Designer, Margaret · The Test Engineer, Gideon · The Checker

MotivationH

Strong enough?

In statics you found the forces on a part: the 50 kN pulling on a tie rod, the reaction at a hinge, the tension in a cable. Equilibrium told you how much force each part carries. It could not tell you whether the part survives. A 50 kN pull is nothing to a ship's anchor chain and fatal to a bicycle spoke.

What decides survival is how concentrated the force is inside the material, and how far the material stretches in response. Those two ideas, stress and strain, are the language of the rest of this level. With them you can answer the questions a mechanical engineer is asked every day: how thick must this bolt be? How much will this shaft twist? How far will this floor sag? When will this bracket crack?

This lesson builds the vocabulary. You will compute stresses and strains, link them with Hooke's law, read the stress–strain curve of a real metal, see why heating a constrained rail creates enormous forces, and discover that stress at a point is not one number but a small matrix, whose eigenvalues tell you where the material is most at risk.

IntuitionH

Cutting a bar in your imagination

Take a steel rod pulled by a force FF at each end. Equilibrium of the whole rod is trivial: FF to the left, FF to the right. Now imagine slicing the rod anywhere along its length and looking at the left piece alone, as a free body. It is still in equilibrium, so the material on the other side of the cut must be pulling it with a total force FF. That pull is spread over the whole cut face, every square millimetre of steel holding on to its neighbour.

FFimaginary cutFσ = F / Afree body of the left piece
An imaginary cut through a bar in tension. The left piece is still in equilibrium, so the cut face must carry the force F, spread over the area A. Away from the ends the spread is uniform, and its intensity is the normal stress σ = F/A.

The intensity of that internal force, force per unit area, is the stress. Double the force and the stress doubles; double the area and it halves. A thick rope and a thin thread made of the same fibre fail at the same stress, which is why stress, not force, is what we compare with the material's strength.

The rod also gets longer. A 2 m rod stretches twice as much as a 1 m rod under the same stress, because every centimetre of it stretches by the same small amount. So the natural measure of deformation is stretch per unit length, the strain, which is dimensionless. And a stretched rod gets slightly thinner, like a rubber band, which is Poisson's effect.

Analogy, not a formal construction

Think of a crowd holding hands in long parallel lines, everyone leaning back to resist a pull. The total pull is the force. How hard each person must grip is the stress: add more lines of people (more area) and each grip gets easier. How much each arm stretches is the strain: a longer line stretches more in total, but each arm stretches the same.

DefinitionsH

Stress, strain and Hooke's law

Definition— normal stress

When a force FF acts perpendicular to a cut of area AA and is spread uniformly, the normal stress is σ=F/A\sigma = F/A. Tension is positive, compression negative. The SI unit is the pascal (1 Pa = 1 N/m²); engineers use megapascals, and 1 MPa=1 N/mm21\ \text{MPa} = 1\ \text{N/mm}^2, which makes hand calculations in newtons and millimetres painless.

Definition— shear stress

When a force VV acts along (parallel to) a cut of area AA, the average shear stress is τ=V/A\tau = V/A. A pin in a clevis, a bolt in a lap joint and a punch cutting sheet metal are loaded mainly in shear.

Definition— normal and shear strain

A line of original length LL that stretches by δ\delta has normal strain ε=δ/L\varepsilon = \delta / L. A right angle in the material that closes by a small angle γ\gamma (in radians) has shear strain γ\gamma. Strains in metal parts are tiny, typically below 0.0020.002, so they are often quoted in microstrain (1 με=10−61\ \mu\varepsilon = 10^{-6}).

Definition— Hooke's law, Young's modulus and Poisson's ratio

For most engineering materials at small strains, stress is proportional to strain. In uniaxial tension

σ=E ε,εlateral=−ν ε,\sigma = E\,\varepsilon, \qquad \varepsilon_\text{lateral} = -\nu\,\varepsilon,

where EE is Young's modulus (the stiffness of the material) and ν\nu is Poisson's ratio (how much it narrows as it stretches). In shear, τ=Gγ\tau = G\gamma with shear modulus GG. For an isotropic material (the same in every direction) only two of these constants are independent:

G=E2(1+ν).G = \frac{E}{2(1+\nu)}.

Definition— thermal strain

A free piece of material warmed by ΔT\Delta T expands with strain εT=α ΔT\varepsilon_T = \alpha\,\Delta T, where α\alpha is the coefficient of thermal expansion. Thermal strain causes no stress by itself; stress appears only if something prevents it.

Some representative room-temperature values, rounded, to build intuition (always take design values from the supplier's data or a materials standard):

MaterialEE (GPa)ν\nuα\alpha (10−610^{-6}/K)
Structural steel200–2100.3012
Aluminium alloys69–720.3323
Titanium alloys105–1200.32–0.349
Concrete25–400.15–0.2010–12
Glass (soda-lime)700.229
Douglas fir, along the grain11–14—3–5
Rubber0.001–0.01close to 0.5100–200

Wood has no single Poisson's ratio because it is strongly anisotropic: stiff along the grain, soft across it. Rubber's ratio near 0.5 means it hardly changes volume as it deforms. Why atoms produce these numbers, and why some materials are stiffer than others, is the subject of elasticity, plasticity and strengthening in Lumenary Materials; here we take them as measured facts and design with them.

Worked examplesH

Worked examples: a tie rod and a hot rail

Example— A steel tie rod

A round steel tie rod of diameter 20 mm and length 2.0 m carries 50 kN. Take E=200E = 200 GPa and ν=0.30\nu = 0.30.

The area is A=πd2/4=314.2 mm2A = \pi d^2/4 = 314.2\ \text{mm}^2, so σ=50 000 N/314.2 mm2=159.2\sigma = 50\,000\ \text{N} / 314.2\ \text{mm}^2 = 159.2 MPa. The strain is ε=σ/E=159.2/200 000=7.96×10−4\varepsilon = \sigma/E = 159.2 / 200\,000 = 7.96 \times 10^{-4}, about 800 microstrain. Over 2.0 m the rod stretches δ=εL=1.59\delta = \varepsilon L = 1.59 mm, and its diameter shrinks by νεd=0.0048\nu \varepsilon d = 0.0048 mm, about a twentieth of a human hair.

Is 159 MPa safe? That depends on the steel. A common structural steel yields at around 235–355 MPa, so the rod is working at roughly half to two-thirds of its yield strength: reasonable for a static load. The lesson on failure and fatigue makes "safe" precise.

Example— A rail that cannot expand

The same rod is now fixed between two rigid walls at a comfortable temperature and then warmed by 40 K on a summer afternoon. Free, it would expand by εT=α ΔT=12×10−6×40=4.8×10−4\varepsilon_T = \alpha\,\Delta T = 12 \times 10^{-6} \times 40 = 4.8 \times 10^{-4}. The walls keep its total strain at zero, so the mechanical strain must be −4.8×10−4-4.8 \times 10^{-4}, and

σ=−E α ΔT=−200 000×4.8×10−4=−96 MPa.\sigma = -E\,\alpha\,\Delta T = -200\,000 \times 4.8 \times 10^{-4} = -96\ \text{MPa}.

That is a compressive force of about 30 kN on each wall, from a change in temperature alone, and notice that the length of the rod does not appear. Continuously welded railway track lives with exactly this: the rails are anchored firmly to the sleepers and laid at a chosen "stress-free" temperature so that summer compression and winter tension both stay within limits, and engineers watch for the sideways buckling that compressed rails can suffer on very hot days. Bridges avoid the problem the other way, with expansion joints that let the deck move.

ExplanationH

The stress–strain curve

Hooke's law holds only up to a point. To find out what happens beyond it, laboratories pull a carefully machined specimen in a tensile-testing machine, measuring force and extension until it breaks, and plot engineering stress F/A0F/A_0 against engineering strain δ/L0\delta/L_0. The method is standardised (ISO 6892-1 and ASTM E8/E8M) so that results from Pune, Pittsburgh and Pohang can be compared.

engineering strain εengineering stress σyield (0.2% offset)ultimate tensile strengthnecking, then fracturebrittle: fracture0.2%elastic slope = E
Schematic engineering stress–strain curves (strain axis not to scale). A ductile metal (solid line) is linear up to yield, hardens to its ultimate tensile strength, then necks and fractures. The dotted line parallel to the elastic slope, offset by 0.2% strain, defines the yield strength where no sharp yield point exists. A brittle material (dashed line) stays nearly linear until it fractures with little warning.

Reading the curve from left to right:

  • Elastic region. Straight, with slope EE. Unload anywhere here and the specimen returns to its original length.
  • Yield. The curve bends: the material starts to deform plastically, permanently, because dislocations in the crystals begin to glide. Some steels show a sharp upper yield point; most metals bend over gradually, so the yield strength is defined by convention as the stress at which the permanent strain is 0.2%. Draw a line parallel to the elastic part starting at ε=0.002\varepsilon = 0.002; where it meets the curve is Rp0.2R_{p0.2}, the 0.2% proof stress.
  • Strain hardening. Plastic deformation multiplies and tangles dislocations, so the material resists further deformation and the stress keeps rising.
  • Ultimate tensile strength RmR_m, the maximum engineering stress. Beyond it the specimen necks: deformation concentrates in one place, the local cross-section shrinks faster than the material hardens, and the force falls until fracture.
  • Ductility, the strain at fracture (elongation after fracture, as a percentage of the gauge length) or the reduction of area at the neck. A ductile part bends and stretches visibly before it breaks, which is a warning; a brittle part does not.

The fall after the ultimate strength is partly an illusion of bookkeeping: engineering stress divides by the original area A0A_0, but the neck's real area is much smaller. The true stress σtrue=F/A\sigma_\text{true} = F/A keeps rising until fracture. Designers of ordinary parts use engineering values (a part that has necked has already failed); people who simulate forming, crashes and machining need true-stress curves.

ComputationC

Computing it: a tensile test in NumPy

Real test data comes as columns of strain and stress. Here we generate a realistic curve for a mild steel from a simple hardening law, true stress =K(ε0+εp)n= K(\varepsilon_0 + \varepsilon_p)^n with K=600K = 600 MPa, ε0=0.005\varepsilon_0 = 0.005 and hardening exponent n=0.20n = 0.20, convert it to engineering values as a testing machine would report them, and then do what a test laboratory does: find the 0.2% offset yield and the tensile strength.

python
import numpy as np

# A model tensile test of a mild steel: Swift hardening, true stress vs true plastic strain
E = 200e3                                     # MPa
K, eps0, n = 600.0, 0.005, 0.20

ep = np.linspace(0.0, 0.30, 3001)             # true plastic strain
sig_true = K * (eps0 + ep) ** n               # true stress, MPa
eps_true = sig_true / E + ep                  # true total strain
e_pl = np.exp(eps_true) - 1.0                 # engineering strain
s_pl = sig_true / (1.0 + e_pl)                # engineering stress (volume conserved)

# prepend the elastic line from the origin to first yield
e_el = np.linspace(0.0, e_pl[0], 50, endpoint=False)
e = np.concatenate([e_el, e_pl])
s = np.concatenate([E * e_el, s_pl])

# 0.2 % offset yield: where the curve meets the line s = E (e - 0.002)
gap = s - E * (e - 0.002)
i = np.argmax(gap < 0)                        # first point below the offset line
t = gap[i - 1] / (gap[i - 1] - gap[i])        # interpolate between the two points
Rp02 = s[i - 1] + t * (s[i] - s[i - 1])

k = np.argmax(s_pl)                           # ultimate tensile strength
print(f"end of the linear part   = {s_pl[0]:4.0f} MPa")
print(f"0.2% offset yield Rp0.2  = {Rp02:4.0f} MPa")
print(f"tensile strength Rm      = {s_pl[k]:4.0f} MPa at engineering strain {e_pl[k]:.3f}")
print(f"maximum at true plastic strain {ep[k]:.3f}; Considere predicts n - eps0 = {n - eps0:.3f}")
print(f"true stress there        = {sig_true[k]:4.0f} MPa")

print("\n strain   eng. stress (MPa)")
for target in [0.0005, 0.001, 0.002, 0.005, 0.02, 0.05, 0.10, 0.15, 0.20, 0.25]:
    j = np.argmin(abs(e - target))
    print(f" {e[j]:6.4f}  {s[j]:5.0f}  " + "#" * int(s[j] / 10))
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

The program reports a yield strength Rp0.2≈222R_{p0.2} \approx 222 MPa and a tensile strength Rm≈357R_m \approx 357 MPa at about 22% strain, figures typical of a low-strength structural steel. The maximum falls exactly where Considère's criterion predicts, at true plastic strain n−ε0=0.195n - \varepsilon_0 = 0.195, and the true stress there, 435 MPa, is about a fifth higher than the engineering value. The little bar chart shows the two personalities of the curve: in the first 0.1% of strain the stress shoots up to 200 MPa, and over the next 20% it creeps up by only another 150 MPa.

ExplanationH

Stress in every direction: transformation and Mohr's circle

So far the cut was perpendicular to the rod. Cut it at an angle instead, and the force on the cut face has components both normal and parallel to it: a tension rod carries shear stress on inclined planes. This is not academic. Ductile metals yield by slip on planes of high shear stress, which in a tensile test lie at 45° to the axis, and bands of slip at roughly 45° to the axis can sometimes be seen on the polished surface of a yielding steel specimen.

In general, at any point of a loaded part, the state of stress needs more than one number. In two dimensions (plane stress, the usual case at a free surface or in a thin plate) it is three numbers: normal stresses σx\sigma_x, σy\sigma_y on faces perpendicular to xx and yy, and the shear stress τxy\tau_{xy} on those faces. Arrange them as a symmetric matrix, the stress tensor,

S=(σxτxyτxyσy).\mathbf{S} = \begin{pmatrix} \sigma_x & \tau_{xy} \\ \tau_{xy} & \sigma_y \end{pmatrix}.

On a face whose outward unit normal is n=(cos⁡θ,sin⁡θ)\mathbf{n} = (\cos\theta, \sin\theta), the force per unit area (the traction) is t=Sn\mathbf{t} = \mathbf{S}\mathbf{n}. Its normal component is σx′=nTSn\sigma_{x'} = \mathbf{n}^\mathsf{T}\mathbf{S}\mathbf{n} and its shear component along m=(−sin⁡θ,cos⁡θ)\mathbf{m} = (-\sin\theta, \cos\theta) is τx′y′=mTSn\tau_{x'y'} = \mathbf{m}^\mathsf{T}\mathbf{S}\mathbf{n}. Multiplying out and using double-angle identities gives the transformation equations

σx′=σx+σy2+σx−σy2cos⁡2θ+τxysin⁡2θ,τx′y′=−σx−σy2sin⁡2θ+τxycos⁡2θ.\sigma_{x'} = \frac{\sigma_x + \sigma_y}{2} + \frac{\sigma_x - \sigma_y}{2}\cos 2\theta + \tau_{xy}\sin 2\theta, \qquad \tau_{x'y'} = -\frac{\sigma_x - \sigma_y}{2}\sin 2\theta + \tau_{xy}\cos 2\theta.

Theorem— Principal stresses

At every point there are two perpendicular directions (three in 3-D) on which the shear stress is zero. The normal stresses on them, the principal stresses σ1≥σ2\sigma_1 \ge \sigma_2, are the largest and smallest normal stresses on any plane through the point, and they are the eigenvalues of S\mathbf{S}:

σ1,2=σx+σy2±R,R=(σx−σy2)2+τxy2.\sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm R, \qquad R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}.

The maximum in-plane shear stress is RR, on planes at 45° to the principal directions.

Proof

The transformation equations say that the point (σx′,τx′y′)(\sigma_{x'}, \tau_{x'y'}) is the centre c=(σx+σy)/2c = (\sigma_x+\sigma_y)/2 on the σ\sigma-axis plus a vector of fixed length RR that turns through angle 2θ2\theta as the face turns through θ\theta: its components are a rotation of ((σx−σy)/2, τxy)\big((\sigma_x - \sigma_y)/2,\ \tau_{xy}\big) by −2θ-2\theta in the plane. So as θ\theta varies, the stress on the face traces a circle of radius RR about (c,0)(c, 0). The normal stress is extreme, c±Rc \pm R, exactly where the circle crosses the σ\sigma-axis, where τx′y′=0\tau_{x'y'} = 0; the shear stress is extreme, ±R\pm R, at the top and bottom of the circle, a quarter-turn (2θ=90°2\theta = 90°) away. Because S\mathbf{S} is symmetric, the spectral theorem gives the same conclusion: an orthonormal basis of eigenvectors in which S\mathbf{S} is diagonal, with the eigenvalues as the extremes of nTSn\mathbf{n}^\mathsf{T}\mathbf{S}\mathbf{n} over unit vectors.

∎

The circle in the proof is Mohr's circle, published by the German engineer Otto Mohr in 1882 and drawn by hand by generations of engineers to read off principal stresses with a compass and ruler. Each face of the element is a point on the circle, and turning the face by θ\theta moves the point by 2θ2\theta.

στX (80, 30)Y (−40, −30)σ₁ = 87.1σ₂ = −47.1τmax = 67.1C (20)2θp
Mohr's circle for σx = 80 MPa, σy = −40 MPa, τxy = 30 MPa. Point X is the stress on the x-face and Y the stress on the y-face. The circle's centre is at 20 MPa and its radius is 67.1 MPa, so the principal stresses are 87.1 and −47.1 MPa and the largest in-plane shear stress is 67.1 MPa. The x-face must turn by θp = 13.3° to become a principal plane, which is 2θp = 26.6° on the circle.
ComputationC

Computing it: rotating the element and finding principal stresses

The transformation is just nTSn\mathbf{n}^\mathsf{T}\mathbf{S}\mathbf{n}, so a few lines of NumPy can turn the element through every angle, and numpy.linalg.eigh, the eigenvalue solver for symmetric matrices, finds the principal stresses directly. The last part does the same for a full three-dimensional stress state, where hand formulas become painful and an eigenvalue solver is simply the right tool.

python
import numpy as np

# Plane stress at a point (MPa): sigma_x, sigma_y, tau_xy
sx, sy, txy = 80.0, -40.0, 30.0
S = np.array([[sx, txy],
              [txy, sy]])

print(" theta   sigma_x'   tau_x'y'")
for deg in range(0, 181, 15):
    th = np.radians(deg)
    n = np.array([np.cos(th), np.sin(th)])     # normal of the rotated face
    m = np.array([-np.sin(th), np.cos(th)])    # direction along that face
    print(f" {deg:4d}   {n @ S @ n:8.1f}   {m @ S @ n:8.1f}")

# Mohr's circle
c = (sx + sy) / 2
R = np.hypot((sx - sy) / 2, txy)
print(f"\nMohr's circle: centre {c:.1f} MPa, radius {R:.1f} MPa")
print(f"principal stresses {c + R:.1f} and {c - R:.1f} MPa; max in-plane shear {R:.1f} MPa")
print(f"principal angle {np.degrees(0.5 * np.arctan2(2 * txy, sx - sy)):.1f} degrees")

# The same answer from an eigenvalue solver
vals, vecs = np.linalg.eigh(S)                 # ascending order for symmetric matrices
print("eigenvalues:", np.round(vals[::-1], 1))
v = vecs[:, 1]
print(f"direction of sigma_1: {np.degrees(np.arctan2(v[1], v[0])) % 180:.1f} degrees")

# A full 3-D stress state at a point inside a part (MPa)
S3 = np.array([[ 50.0,  20.0,  0.0],
               [ 20.0, -10.0, 15.0],
               [  0.0,  15.0, 30.0]])
p = np.linalg.eigvalsh(S3)[::-1]
print("\n3-D principal stresses:", np.round(p, 1), "MPa")
print(f"absolute maximum shear (s1 - s3)/2 = {(p[0] - p[2]) / 2:.1f} MPa")
print(f"invariant check: trace {np.trace(S3):.1f} = sum of principals {p.sum():.1f}")
Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

The table shows the normal stress climbing from 80 MPa to a peak of 87 MPa near 15° and the shear stress passing through zero there; near 58° the shear reaches its extreme of −67-67 MPa. Mohr's formulas and the eigenvalue solver agree: principal stresses 87.1 and −47.1-47.1 MPa, with σ1\sigma_1 acting on the plane turned 13.3° from xx. In three dimensions the principal stresses are 56.8, 33.3 and −20.2-20.2 MPa, and their sum equals the trace of the matrix, 70 MPa, as it must: the trace is an invariant, the same in every set of axes.

ExplanationH

How engineers measure and use stress

Nobody can see stress. Engineers infer it from strain, which they can measure, and from models, which they can compute.

  • Tensile testing gives the material's EE, Rp0.2R_{p0.2}, RmR_m and elongation. Test laboratories follow ISO 6892-1 or ASTM E8/E8M, which fix specimen shapes, strain rates and how to compute each property, and they report results on test certificates that travel with each batch of steel or aluminium. Design codes and handbooks (for example the ASM Handbooks, or the material tables in national structural codes) give minimum guaranteed values, not averages.
  • Strain gauges are thin foil grids glued to a surface whose electrical resistance changes in proportion to strain. A rosette of three gauges at 0°, 45° and 90° measures the three in-plane strain components at a point; Hooke's law and the transformation equations then give the principal stresses. Strain gauges are used everywhere from bridge monitoring to the load cells in kitchen scales.
  • Digital image correlation tracks a speckle pattern painted on a part with cameras and computes a whole field of surface strains, which is now routine in research and aerospace testing.
  • Finite element analysis, the subject of the last lesson of this level, computes the full stress tensor at millions of points in a complicated part. The software then reports principal stresses and a combined "equivalent stress", which you will meet in failure and fatigue.

When you see a stress contour plot, every colour on it came from the ideas in this lesson: a tensor at each point, its eigenvalues, and a comparison with a strength measured in a tensile test.

History & global context

A short history

Robert Hooke stated his law in 1678 as a Latin anagram resolved to ut tensio, sic vis, "as the extension, so the force", from experiments with springs, wires and watch springs. Thomas Young described the modulus that bears his name in 1807, though not yet as stress over strain. Claude-Louis Navier and Augustin-Louis Cauchy, in Paris in the 1820s, turned elasticity into a field theory: Cauchy introduced stress as a quantity acting on every plane through a point and showed that it transforms as what we now call a tensor. Siméon Denis Poisson predicted the lateral contraction ratio from a molecular model (his model gave ν=1/4\nu = 1/4 for every material, which experiments later showed was too simple). Otto Mohr's graphical circle followed in 1882, and William Rankine, Barré de Saint-Venant and many others turned the theory into engineering practice for the railways, bridges and boilers of the nineteenth century.

Common misconceptionsH

Common misconceptions

Misconception

"Stress is force." Stress is force per unit area, and it is what the material feels. A 10 kN load is harmless on a 100 mm diameter column and destructive on a 3 mm wire. Compare stresses with strengths, never forces with strengths.

Misconception

"Stiff means strong." Stiffness (EE) says how much a part deflects; strength (yield or tensile strength) says how much stress it survives. Every steel, from soft wire to a hardened bearing race, has nearly the same E≈200E \approx 200 GPa, yet their yield strengths differ by a factor of ten. Glass is about as stiff as aluminium and far less tough.

Misconception

"The engineering stress–strain curve falls after the peak, so the metal gets weaker as it is stretched." The true stress keeps rising; the engineering stress falls because the force falls as the neck thins, while we keep dividing by the original area.

Misconception

"Poisson's ratio can be anything." For a stable isotropic material, −1<ν<0.5-1 \lt \nu \lt 0.5. Values approaching 0.5 mean the material is nearly incompressible (rubber); cork, close to 0, hardly bulges when squeezed, which is why it seals a bottle neck so well. Engineered auxetic structures can even have a negative ratio and widen when stretched.

Misconception

"If there is no shear stress on my x and y faces, there is no shear stress anywhere." A rod in pure tension carries a shear stress of half the axial stress on 45° planes, and that shear is what makes ductile metals yield.

Exercises

Exercises

1. Stress and strain

Warm-upHuman

A flat aluminium hanger bar with a cross-section of 6 mm × 25 mm carries a tensile load of 12 kN. What is the normal stress in the bar, in MPa?

2. Stress and strain

Warm-upHuman

Two rods have identical dimensions and carry the same load, well within their elastic range. Rod A is a high-strength steel (yield strength 900 MPa); rod B is a soft, low-carbon steel (yield strength 250 MPa). Which statement is right?

Choose one

3. Stress and strain

CoreHuman

An aluminium bar (E=70E = 70 GPa, α=23×10−6\alpha = 23 \times 10^{-6} K⁻¹) is fitted snugly between two rigid supports and then warmed by 30 K. Assuming it stays straight and elastic, what is the magnitude of the compressive stress in the bar, to the nearest MPa?

4. Stress and strain

CoreHuman

At a point on the surface of a bracket, σx=60\sigma_x = 60 MPa, σy=−20\sigma_y = -20 MPa and τxy=30\tau_{xy} = 30 MPa. What is the largest principal stress σ1\sigma_1, in MPa?

5. Stress and strain

CoreHuman

Which of these statements about Poisson's ratio ν\nu of an isotropic, linear-elastic material are true? Select all that apply.

Choose all that apply

6. Stress and strain

CoreComputational

Write principal_stresses(S), which takes a symmetric 3 × 3 stress tensor (a NumPy array or nested list, in MPa) and returns a pair:

  1. a tuple of the three principal stresses (s1, s2, s3) in descending order, and
  2. the absolute maximum shear stress (s1 - s3) / 2.

Use an eigenvalue solver. The tests include uniaxial tension, hydrostatic pressure, a case where the largest shear acts out of the plane, and a rotated tensor (the principal stresses must not depend on the axes).

Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

7. Stress and strain

StretchComputational

A test laboratory gives you a tensile curve as two arrays, strain (dimensionless, increasing) and stress (MPa), and Young's modulus E (MPa). Write offset_yield(strain, stress, E, offset=0.002) that returns the offset yield strength: the stress where the curve first crosses the line stress = E * (strain - offset), found by linear interpolation between the two data points either side of the crossing. If the curve never crosses the line, return None.

Runs entirely in your browser, in an isolated worker. Nothing is sent to a server.

Further reading and resources